FastScions.com now carries a full line of wheel spacers w/ extended studs for all Scion models.

5MM

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=724

15MM

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=725

20MM

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=726

25MM

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=727

If you need spacers, take advantage . . .

Anyone have experience with these?

Scott

can you do a special price if i get 2 sets? both 15mm and no 10mm? :(

i had them on my xa. worked great.

1. Do they weaken the suspension more overtime?

2. Racing Safe? As in Auto X?

PM sent.

NO they do not weaken the susp more overtime and YES they are racing safe, including Auto X.

Check their website out for yourself for more info . .

www.ichibausa.com

bump:

btw i replied to your reply and i didnt get anohter reply :doh:

same here i need a 15mm and a 20mm set can u pm me a price. thanks.

im interested in the same thing as davedave...
could you send me a pm too? =)

same here i need a 15mm and a 20mm set can u pm me a price. thanks.

u gonna use them on stock wheels? 20 mm on the stock wheels will be tight man... i have rolled fenders and ran a 25mm spacer on the stock wheels and was rubbing.... a lot

same here i need a 15mm and a 20mm set can u pm me a price. thanks.

u gonna use them on stock wheels? 20 mm on the stock wheels will be tight man... i have rolled fenders and ran a 25mm spacer on the stock wheels and was rubbing.... a lot

no not on stockers. i got some +49 et wheels. i kno i kno...its bad but can u blame me?
just take a look
http://i3.photobucket.com/albums/y73/93greenakkord/CIMG8130.jpg

yea but that will give that wheel a +29 offset, thats still kinda low. are your fenders rolled? and will you be running camber?


i would get 15s for the rear instead, just to be safe, and 10s in the front :P just like me! haha but idk if i need them, the wheels im gettin in a couple months have a +35 offset. these would be just for stock, and each time i replaced them i would need to change the studs....

yeah i got a ____ load of camber in the rear. right now i got et38 wheels with the same width as my new ones, and with the car dropped, i can still fit a finger in between the fender and the tire. and for the front. i have a 5mm spacer on a et 38 which makes it 33 and i do not rub. so with a 15mm in the front, ill be at 34 which is 1 mm less then now. so ya ill be fine. and if i have to i can run negative camber w/ my camber plates.

yea but if you do that you're going to chew through tires plus your handling will decrease, and you will put too much stress on the rear suspension. i would play it safe and if you want 15 in the front i would do 15 in the rear too. thats just my 2 cents, im currently running maybe 1.5 degrees of neg camber in the rear and i think thats too much.

yea i feel u on the tires. but low profile tires wear out very fast neways. and i will mostlikley get some that will let me rotate them alot. i dont mind rotating them every 2k miles. its that slammed look that im goin for. as far as the longer studs go, just get some open ended lugs and ull be fine, thats what i plan on doing.

PM's sent.

yea i feel u on the tires. but low profile tires wear out very fast neways. and i will mostlikley get some that will let me rotate them alot. i dont mind rotating them every 2k miles. its that slammed look that im goin for. as far as the longer studs go, just get some open ended lugs and ull be fine, thats what i plan on doing.

thats true man, plus they look sick too :wink:

wats the best for stock wheels to be flush? I know the back must be like +5 more than the front. maybe 10 front and 15 rear?

15mm in the rear and 10mm in the front.

btw 1fast scion do you guys ahve 10mm spacers? i would like to know the price shipped for 5mm and 10mm if you dont have tens then just the 5mm shipped. thanks!

sssssooo they dont sell 10s?

idk thats what im tryin to find o ut :P

1Fast you have a PM

PM sent.

what about an anwer on the 10mm spacers

ichiba does not make 10mm spacers for the tC

damnit

just do 15 front 20 rear.

man u crazy :P

1fast pmed

anyone got a walkthrough on throwing these on?

yea, do a search

wow that is a really helpful response?!

I checked through tech and there isnt one on there.

you didnt check enough,...
http://www.scionlife.com/forums/viewtopic.php?t=147154

thanks, I appreciate the help.

1 fast payment sent.

payment received.

we are out of the stock on the 20mm, but it is due in from Ichiba on Friday.

depending on what time it gets here, it will go out either Friday or first thing on Monday.

Thanks bud.

DoH!

whats the max you can go in the front or rear without new bolts?

they just came in atodak!

going out tomorrow !

PM sent with tracking.

Thanks again!

TY

Any discounts for 2 sets of 15mm spacers shipped to 94134?
Thanks

Pm sent

can u pm me a price of 5mm shipped for a 06 xb?

PM sent.

how do we order these?

PM sent.

bump:

bump:

so has anybody tried the 25mm, I was thinking about giving them a shot, I am running a set of 17 X8.5 with s-techs, wonder if they will work. How much for a 2 sets of 25mm shipped to zip 70003

PM sent.

bump:

bump:

bump for sum kick arse spacers.

bump!

Front 15MM
http://i230.photobucket.com/albums/ee73/atodak/QPikS162.jpg
Rear 20MM
http://i230.photobucket.com/albums/ee73/atodak/QPikS161.jpg

bump:

In terms of strentch compared to the stock ones, what is the difference ? I need something that is extremely stronger and can take heat/stress of the track. Spacers/extended studs dont really make a diff to me. Just want something stronger.

pm sent

PM replied.

In terms of strentch compared to the stock ones, what is the difference ? I need something that is extremely stronger and can take heat/stress of the track. Spacers/extended studs dont really make a diff to me. Just want something stronger.

Definitely the way to go. Many of our customers use their tC on the track every other weekend. No complaints.

check out Ichibausa.com for more info.

sounsd good, not exactly sure if I need spacers even though ? are they just to compensate negative offset wheels correct ? so like if I has a 35mm wheel and i got the 5mm spacers it would be sitting at 40mm ??

No, you will be at 30mm. It will cause your wheel to stick out 5mm more. kanundrum, YGPM.

OOOO crapo! so it would be antiprogress for me. I have 38mm wheel offset right now so I def wouldnt need them to be 33. Basically I will be adding 235 tires to my 38MM rim so not exactly sure what I would need so that I dont rub while im taking sharp turns with an agressive camber setup

bump:

bump:

bump:

bump:

bump:

bump:

bump for an excellent product

Hey 1fastscion...........

My wheels are 18 x 7 with a 40 offset wrapped in nexxon 225/40R18 tires do u think 15mm in the front and 20mm in the rear would be safe without having to roll the fenders I am also on TRD springs? I measured the gap between the wheel and the fender and in the front its about 1/2 an inch and the rear is about 1 inch. Has there been any problems with vibration and the steering wheel shaking at high speeds? Do these wheel spacers work with any aftermarket wheels?

Thank you.....any imput would be greatly appreciated :bow:

There are NO vibration or shaking at high speeds and of course these are compatible with aftermarket wheels.

With an 18X7, you should be fine with that setup. However, I cannot guarantee it.

Well in that case what kind of deal can i get for 15mm & 20mm shipped to 95366?

PM sent.

1 fast.......payment sent.....cant wait!

ill try and get those out today for ya!!

I would greatly appreciate it :bow: :clap:

Have you shipped it yet?????

:tap:.......................waiting

my bad bud, the 20 wasnt in stock. but coming in today!!

ill provide tracking ASAP, thanks for your patience.

Man...............if i knew it would take this long to ship i would not have ordered them! Whats going on....how come you did not tell me they were not in stock when i ordered them! Just for that i should get 10% off! Hurry up already.......................PLEASE..............I am getting impatient! :nails: :tap:

PM with tracking was sent. thanks for patience.

any other takers?

15mm and 20mm shipped to 90019?

PM sent.

bump:

i'd like to buy the 5mm. how should i make payment?

PM sent.

bump:

bump:

all spacers in stock!!

bump:

Any chance on getting stock length spacers made of the same material so we can have stock stronger ones are available???

wish i could help . . but we only sell Ichiba aftermarket spacers and studs.

how much are the studs?

studs not sold individually . .

bump:

bump:

how much longer are the studs on the 5mm spacers?

Interested in a set of 15's or 20's to bump out my rear wheels a bit. How much is the shipping for a set of these?

PM sent/

???

5MM Spacer Studs:

Thread Size: 12x1.5

Thread Length: 35MM

I dont know the length of the stock spacers to begin with, but maybe this helps . .

bump:

bump:

bump:

bump:

bump!!!!!

HEY GUYS,

NEW SPACERS & STUDS ADDED!!

We now offer 10mm Wheel Spacers for all Scion models

http://i123.photobucket.com/albums/o303/1FastScion/15mm_scion_wheel_spacers.jpg

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=851

ICHIBA has also released their Version II BOLT-ON series wheel spacers for scion models . . available in 15mm, 20mm & 25mm sizes!!

http://i123.photobucket.com/albums/o303/1FastScion/ichiba_scion_spacer_v2.jpg

http://fastscions.com/index.asp?PageAction=VIEWPROD&ProdID=852

Last but not least, we are selling individual ICHIBA extended wheel studs, sizes 35mm, 45mm & 50mm to fit spacer sizes from 5mm - 20mm.

http://i123.photobucket.com/albums/o303/1FastScion/ichiba_scion_extended_wheel_stud.jpg

http://fastscions.com/index.asp?PageAction=VIEWCATS&Category=388

PM for pricing and availability!!!

How much for Version II BOLT-ON series wheel spacers size 15mm and 20mmm shipped to 95366?

PM sent homie!

BUMP!

brand new items!!

bump

stocked on these items!!

bump:

bump!!

in stock!!

How much for 15mm bolt on for xb2 shipped to 92704?

PM sent!

Hi, i know you PMed me in regards to wheel spacers. Can I get a price for 2 pairs of 10mm spacers? And do these come with extended studs? Thanks!

Yes, these come with extended studs!!!

Everything u need for a complete installation.

PM sent with pricing and availability!!!

bump it up!

Can you please PM me a price for 2 sets of 5mm shipped to 92126 please? Thanks!

PM sent.

This is a pretty easy question for most of you guys, I don't know much about the spacers or wheel offsets.
But I just got wheels that are 17x7 with a +38 offset, so which spacers would be best for me to make the wheels look best?

Oh, and bump for fastscions.com, good company and great to deal with.

bump!

bump

bump

price on 15mm for 04 xb shipped to 70726

Are there instructions posted anywhere on how to do the rear spacers? I haven't looked at it very much, but I hear you have to pull the rear hub off.

u might want to check with ichiba.

www.ichibausa.com

bump!

How much for Version II BOLT-ON series wheel spacers size 15mm and 20mmm shipped to 95366?

PM sent!

bump!

bump!

oh yea!

in stock peeps . .

bump!

bump!

all types of spacers and studs for all scion models!!!

How much could you do a pair of 15mm for tc shipped to 90263?
Thanks.

PM sent.

Thanks!

i need a pair of 20mm shipped to 90242 plz. (2 sets) im local in Downey if I could arrange a pickup?

PM Sent!

PM responded!

take advantage guys!

would 15 int he front and 20 in the back make if flush with stechs on? or will it rub

I think 15 front and 10 rear - someone please correct me if I'm wrong.

they dont have 10 in here..so 20 front and 15 rear?

That configuration will rub unless you run negative camber on your setup.

would 15 int he front and 20 in the back make if flush with stechs on? or will it rub

x2

i was thinking 15 front and 20 rear.

WE DO HAVE 10MM!!!

www.fastscions.com/toyotascion10mmwheelspacers.aspx

Cool.. you should update the 1st post so that people can see it.

yea we did, check out page 6 of the post

www.scionlife.com/forums/viewtopic.php?t=207499&postdays=0&postorder=asc&&start=100

how much for 15mm?
could i pick them up?

PM sent :)

yea we did, check out page 6 of the post

www.scionlife.com/forums/viewtopic.php?t=207499&postdays=0&postorder=asc&&start=100

well people dont look at page 6 to get all their info :P..jk

might be getting some soon is there like some type of thing we put to have a scion life discount or somthing?

yes, enter "Scionlife" during checkout and receive 5% off of your order!!

bump!

now is the time to get spacers for your Scion!

5mm, 10mm, 15mm, 20mm & 25mm all available!

bolt-on wheel spacers available in 15mm, 20mm & 25mm!!

How much for one set of 5mm shipped to 95366??

i got a 19X8.5 up front with a +35 offset and i need to put 10 or 15mm spacer to clear my caliper.....will it work? any chance or constant rub?

You might need to roll your fenders. By the way what tires and size are u running on those bad boys

i have the rears rolled and i got 19X9.5 back there and its all good...but up front what is there to roll? the fender is pretty much flat

How much for one set of 5mm shipped to 95366??

bump!

what spacer's will make the rear tires sit flush with the front's? my offset is +48 i only need 2

PM's sent guys!

bump!!

my 2 sets of 20 mm fit perfect guys, however I could do with another 5 mm in the back to even out

how much would I be able to get the 25mm for picked up?

PM sent!

bump it up!

come and get em . .

bolt-on versions also available!!

www.fastscions.com/search.aspx?manufacturer=146

Come And Get Em!

All Spacers Ship in 1 to 3 Buisness Days!

Don't Forget About Your ScionLife 5% Discounts!!

http://www.fastscions.com/search.aspx?manufacturer=146

by any chance you have any pics of an xb with 25mm spacers in rear ??? thanks???

by any chance you have any pics of an xb with 25mm spacers in rear ??? thanks???

ill check it out . . .

Ichiba 15mm Version II for tC shipped to 95148 please.

PM sent bud!

my 2 sets of 20 mm fit perfect guys, however I could do with another 5 mm in the back to even out

how much would I be able to get the 25mm for picked up?
you mind posting a pic of the spacers... thanks

my 2 sets of 20 mm fit perfect guys, however I could do with another 5 mm in the back to even out

how much would I be able to get the 25mm for picked up?
you mind posting a pic of the spacers... thanks

my 2 sets of 20 mm fit perfect guys, however I could do with another 5 mm in the back to even out

how much would I be able to get the 25mm for picked up?
you mind posting a pic of the spacers... thanks

my 2 sets of 20 mm fit perfect guys, however I could do with another 5 mm in the back to even out

how much would I be able to get the 25mm for picked up?
you mind posting a pic of the spacers... thanks

do i really need to put in the extended studs for 5mm? just wanting to know before hand

^ I did not and it has been fine. I just tighten them probably like once a month just to make sure.

how much for a set of 5mm and 10mm for the tc picked up

so the 25mm will not need extended studs, right? I just use the provided bolts to bolt down onto the hub, then essentially the rim to the spacer?

pm price as well please.

hey, is there a possible way to cancel my order? i tried looking for a way on the website but i cant seem to find a way to login?

PM's Replied!!!!

purchasing these soon, but whats the difference in version I to II? no bolt on to bolt on? on version II, we dont need to get longer bolts correct? there is no 10mm in version II? the toyota celica has the same wheel pattern as us and they have a 10mm in version II? would it be possible to purchase them?

The version 1 is not bolt on and the Version 2 is bolt on. You do not need to buy wheel studs as the version 2;s come with new ones. As for the celica i am unsure if it will work but from what you say it sounds like it might.

IN STOCK BUMP!!!!!

First question, do u ship to Canada ?
Second, can u install those 5mm on the front of XB 1gen ?
Third, how much for 5mm and 10mm with shipping to Canada L9T0C3 ?

^ I see u have them already. You need another set?
BUMP!!!!!

BUMP!!!!

BUMP!

BUMP!

stocking all bolt patterns and sizes!

^ I did not and it has been fine. I just tighten them probably like once a month just to make sure.
Are you saying the spacers are getting loose once a while? I'm nurvous!

What is the difference between this...

http://www.fastscions.com/Ichiba-25mm-Bolt-On-Wheel-Spacers-Version-II.aspx

and this...

http://www.fastscions.com/Ichiba-25mm-Wheel-Spacers-Scion.aspx

I know it says bolt on... but can you explain?

Also, is 25mm the biggest you have? Can you get to 17112 before this coming Saturday (8/8)

pmed