I just got my xB back from the shop after they installed my SPEC stage 3 clutch. All I can say is WOW. This thing sticks like a clutch is suppose to. I will hit the local dyno as soon as I get my header installed.

how much for parts and install?

David at SPEC clutch sponsored me, but my labor was $280 at a friends shop. Toyota wanted $400. If your near NC I can get a good deal on clutch installs.

sweet....

sweeet.. I have one in my basement waiting for spring and a hotckis front sway :).

Did you leave in the stock fly wheel? Did they resurface it for you in the 280 price?

cant wait to see what kind of times u post up with ur new clutch. have fun

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

That's my plan too. New flywheel, clutch, and synthetic in the tranny. But not for some time until after the surgeries. I'll order in the next month or tow due to the lag time on some of the parts.

man i know i can do rwd clutches but i've never touched a fwd . wonder how long it'd take me. i better not even try

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

That's my plan too. New flywheel, clutch, and synthetic in the tranny. But not for some time until after the surgeries. I'll order in the next month or tow due to the lag time on some of the parts.
Great minds think alike :wink:

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

That's my plan too. New flywheel, clutch, and synthetic in the tranny. But not for some time until after the surgeries. I'll order in the next month or tow due to the lag time on some of the parts.
Great minds think alike :wink:

I think its the vibes I get off of the monitor when Munch is on. :wink:

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

That's my plan too. New flywheel, clutch, and synthetic in the tranny. But not for some time until after the surgeries. I'll order in the next month or tow due to the lag time on some of the parts.
Great minds think alike :wink:

I think its the vibes I get off of the monitor when Munch is on. :wink:
LMAO :lol: :lol: :lol:

LMAO, you two want a room....

i kid, i kid....

I just got my xB back from the shop after they installed my SPEC stage 3 clutch. All I can say is WOW. This thing sticks like a clutch is suppose to. I will hit the local dyno as soon as I get my header installed.

Can't wait to see the dyno results on this one. Do you have a link to where the clutch was purchased? :D

LMAO, you two want a room....

i kid, i kid....

Dave,

You got one w/ a two post lift, alignment rack, tire mounting and balancing machine, lathe, mill, Miller welder, a couple of Snap-on roll arounds, mandrel bender, compressors, and air tools?

mandrel benders are bank bro think 15-25k each. . hey how's the engagement?

I only have 10000 miles. My flywheel looked new. Just scuffed it up a little. I was going to do the JUN just don't want the 16 week down time when I replace it to get a new one. I plan on getting stonger half shafts for the front and using 15"s to race.

Heres the link to SPECS webpage.

http://www.specclutch.com/

LMAO, you two want a room....

i kid, i kid....

Dave,

You got one w/ a two post lift, alignment rack, tire mounting and balancing machine, lathe, mill, Miller welder, a couple of Snap-on roll arounds, mandrel bender, compressors, and air tools?

no lathe, mill or wleder.... yet
the others i have access to when i need....

Sweet 8) Did you put synthetic gear oil in the tranny :?: I'll be doing my clutch and Jun flywheel myself sometime next week. My flywheel should be here on monday. I'm hoping for BIG improvments 8)

what clutch did u get and how much did it set u back?

also how much did u pay for ur JUN flywheel?

where did u purchase both of them from cause i plan on ordering a similar setup soon since my clutch is giving out towards the top of 3rd.

seems as if the factory pressure plate has a clamping force of an astonishing 100lbs haha

the flywheel he got from Darren, look in the privat party classifieds for the thread...

Yeah, I really want to get a lighten pully and flywheel as well, kinda do them all at once. (oil too). BUT, I'm outta cash so I gotta wait. I just can't see putting in the clutch without the flywheel at the same time, but that might happen :(

the flywheel he got from Darren, look in the privat party classifieds for the thread...
Yup ypu're right about the flywheel. It should be here in about an hour when UPS comes :D . I got a stage 4 clutchmasters clutch to go with it. The total for the package set me back alittle over $800 I think. I don't count pennies. If I want something I just buy it :lol:

I used to have access to a mill and lathe when I did gunsmithing.