I heard HID doesn't fit in them.. is this true? can u make a HID fit in them? :pray: :pray: i am planning to buy a set but if HID don't fit, i'll stick with the OE ones... please help..

I heard the same thing.

Just need whatever HID bulb-type that the headlight uses (h1 or h3 or h7 im guessing)

They fit because that's what I have in mine. All you need is a set of 9006 HID bulbs and H4 balasts and you're good to go. Check out the link in my sig for pictures of my HID setup.

i think they might fit

http://memimage.cardomain.net/member_images/8/web/800000-800999/800847_10_full.jpg

Hey Munch ... is the picture with your high beams or low beams on?

http://memimage.cardomain.net/member_images/8/web/800000-800999/800847_10_full.jpg




nice! :bow: can't wait to get mine and install a HID>>> low beam ,high beam and fog lights..

Hey Munch ... is the picture with your high beams or low beams on?
That's my low beams. The high beams are much more intense :bow:

can I suggest maybe you write a how-to and take some pictures of how you did it if you can. I would be interested in doing something like this if I could get a better understanding of how. Also how much did the total project run?

Mike

can I suggest maybe you write a how-to and take some pictures of how you did it if you can. I would be interested in doing something like this if I could get a better understanding of how. Also how much did the total project run?

Mike
I just brought the headlights and my friend had a set of HID's that came out of a Maxima. I used the ballasts and brought a set of 9006 bulbs. Wired them up and I was good to go. The Maxima used diffenet bulbs , so I couldn't used them

http://memimage.cardomain.net/member_images/8/web/800000-800999/800847_10_full.jpg

what gauges are those? not your center gauge but the digi ones? also what are the bulb sizes for those projectors,thanks

also what are the bulb sizes for those projectors,thanks[/quote]


9006 low, 9005 high

http://memimage.cardomain.net/member_images/8/web/800000-800999/800847_10_full.jpg

what gauges are those? not your center gauge but the digi ones? also what are the bulb sizes for those projectors,thanks
The gauges are Nordskog Street Series Digital Gauges and the bulb sizes are 9006 for the low beams and 9005 for the high beams.

thanks for the replies i really like your gauges im looking for blue digitals but the only ones i have found are pretty pricey and not exactly what i am looking for. thanks again

well i got my dual halo headlights today and HID fits just perfect but i have a change in mind so it's up for sale.. SOLD!

are your dual halo lights black housing or chrome?

Those digital guages are hot, very retro digital.

[quote=Munch]
what gauges are those? not your center gauge but the digi ones? also what are the bulb sizes for those projectors,thanks
The gauges are Nordskog Street Series Digital Gauges and the bulb sizes are 9006 for the low beams and 9005 for the high beams.

Can we see a daytime shot of your gauges. I'm intrigued...

Can we see a daytime shot of your gauges. I'm intrigued...
I don't have any recent pics of the 4 gauges, but in my sig there is a pic of 3 of them in the daytime.

what is the total cost in parts for running a HID setup? I am interested in doing this but was wondering what it would run to do so.

Mike

what is the total cost in parts for running a HID setup? I am interested in doing this but was wondering what it would run to do so.

Mike

check out www.hid-light.com

ok i put on my projectors and the lights they came with are super dim, i hope my luminics come in soon! i guess they are ok overall the lights seem a bit uneven though.

:clap: :clap: :clap: those lights are nice as hell i give u mad props for that. where can i find them like yours, cuz i have regular hid bulbs (just regular blue headlights) but i want to get some dual halo projectors. any help please?

eBay

yep they sell lots and lots on ebay..prices have dropped on them.

yep they sell lots and lots on ebay..prices have dropped on them.

They are like half the price they were when I bought them.

I'm going to replace mine as soon as some good high quality lights come out without the silly led's.

should of kepted your stock ones.......and upgraded the bulbs.....

or.... open them up and delete the 3 LED ports with a little body work. There -- LED's all gone.

or.... open them up and delete the 3 LED ports with a little body work. There -- LED's all gone.

I'm not that talented and that doesn't help with the quality issues.

like the lens overlapping the fenders.....
or having to rotate the LF bulbs to clear the battery and fuse box
not to mention the overal TIGHT fitment
I had to loosen both fenders, install lights, tighten fenders then install bumper

but they look good and the Halo's are fun

i hope it all works out because it will be nice

go you all's halo's fog up? mine are soooooooooooo fogged up right now its rediculous.

http://img.photobucket.com/albums/v474/_666_jesus_999_/scion/fog2.jpg
http://img.photobucket.com/albums/v474/_666_jesus_999_/scion/fog.jpg

if you all have had this problem, how did you fix it? thought about siliconeing it but im not sure where its leaking in from and its on the actual projector lenses too.

Drill a few holes in the bottom of the headlights. It fixed my fogging problem :lalala:

thanks for the advice, i might give it a try.

many of you with the bad fogging problems also may not have the bulbs completely seated either, allowing a lot of humid air into the housing. The side markers on the dual halos are a very tight fit and may SEEM like they are in - when in fast they can go in further THEN twist-lock into place.

on the dual halos, there is a small hole under each of the 4 projector assemblies where the halo wires exit, also allowing moist air into the housing.

either drill holes as Munch says, or just run the headlights until the heat evaporates the fogging (which is the OEM suggestion on foggy OEM headlights)

There is nothing you can do to ever 110% seal a headlight housing, just doesn't happen - and if you DID manage it, it would all be lost soon as you changed a bulb.

damn i never had that problem just a lil moisture but thats about it ....

mine used to fog up but not that bad....
just a lil lower right corner on the left headlight.
switched bulbs and that went away!

Just got my new Dual Halo projectors for my xB from assembleweb and have a few questions:

What all has to be removed to install them? Bumper? Grille?

Do I need to run load redistors for the LEDs or are they already built in?

Is it better to try and seal them completely or drill the holes as others have done?

i dont know but one of my halo's stopped working and im ____ed!

Just got my new Dual Halo projectors for my xB from assembleweb and have a few questions:

What all has to be removed to install them? Bumper? Grille?
Yes you have to remove bumper and grill.

Do I need to run load redistors for the LEDs or are they already built in?
I didn't and they work fine.

Is it better to try and seal them completely or drill the holes as others have done?
I would try to seal them completely.

Just got my new Dual Halo projectors for my xB from assembleweb and have a few questions:

What all has to be removed to install them? Bumper? Grille?

Do I need to run load redistors for the LEDs or are they already built in?

Is it better to try and seal them completely or drill the holes as others have done?

hey thats who i bought mine from he was real good and i got might lights without delay
but mine where around $325 in all when they first came out now there down in the 125's.
my lights work fine no problems halo's work good led's work awesome and i didnt seal it up or drill holes because i really dont have the fogging up issue.....

be careful with getting them on ebay.. i got mine and they fogged.. also, the ebayer said that they were DOT legal and there is no DOT marking on the lights at all.. look out!!

It doesn't matter where you get them from. They are all made by the same company.

so how can one company sell them for $90 and another company sell them for $400?

Behold, the power of eBay.

these lights own! do you really have to take them apart to seal them or can you just seal the seams with a little love and care? i have this thig about putting car parts in the oven :-\ makes me egey

I paid $59.00 on ebay for mine and I wash my car every week with high pressure and they are still fine.
http://img.photobucket.com/albums/v211/EVILDAVE666/headlighsWeapon-R003.jpg
http://img.photobucket.com/albums/v211/EVILDAVE666/headlighsWeapon-R002.jpg

EvilDave with the super clean TCM :bow:

hope this isnt repetative, im pretty new to all this.

So if i buy the $60 pair off ebay, or the $160 pair.....they are the exact same dual projectors?

no differance what so ever?

hope this isnt repetative, im pretty new to all this.

So if i buy the $60 pair off ebay, or the $160 pair.....they are the exact same dual projectors?

no differance what so ever?

Correct.

yeah thir the same. but since their release, th prices have come down, search with a fine tooth comb to get the price you want.

i saw a set for 61.50, shipping was 45 bucks.

and all you do when you get them is reseal them and get new bulbs or HID lo beams.

sorry still new at this. how would i go about re-sealing them? Where is the best place to pick up some HID lights?

you can check out HIDs in the sponsored section once you hit over 50 total post. for the resealing, you can do the ovon method and get some silacone and reseal them from there. check th e gallery for people with the dual haloes. most of them resealed them. give those people a pm and ask around.

Sigh... well I just got my projectors and I put em' in and everything but they just don't look fit... as in the bumper seems to be sinking down some and around the headlight housing it just doesn't seem snug.. is this with everyone? Just doesn't look right to me. Oh and will the Luminic bulbs be fine to replace them with?
Thanks

Luminics or Silverstars.

And, yes the fitment is an issue with most people.

How is it just with MOST and not just all or none?

Cause I don't know everybody.

Ah I see then.. your just making an assumption... mmk

I'm going off of personal experience.
My headlights don't fit right and I haven't seen any yet that did.

Yeah so you know exactly what I'm talkin about then? Just wanna make sure I'm not alone here