Does anyone know the specific measurements to where the rear " bB " badge is placed? Does it go over the exactly the same location the " xB " badge sits on? I just want to know if there's a particular spot before I remove the xB and place the bB badge. I didn't want it to sit too high or sit to low from where it's suppose to go. Any help is appreciated. :D

you can put it any where u want it... I think it looks cool in the top center or in the lower right hand corner.

good luck


-ryan

you can put it any where u want it... I think it looks cool in the top center or in the lower right hand corner.

good luck


-ryan

Ditto to Ryan

On a true JDM bB where does it go...this ? has been asked at least 5 times by me with no answer...does anyone know?

On a true JDM bB where does it go...this ? has been asked at least 5 times by me with no answer...does anyone know?


Here's the source.... Toyota Japan!
:D

http://www.toyota.co.jp/Showroom/All_toyota_lineup/bB/menu/exterior.html

It's goes in the lower right corner, just like the xB logo.

I'm Jealous, they get moonroofs!

Why not glue some magnets on it

http://www.wondermagnets.com

and attach it magnetically? Then you can change its position at your slightest whim!

http://www.scionlife.com/gallery/data/500/bB_rear_emblem.jpg

http://www.scionlife.com/gallery/data/500/bB.jpg
(I'm gonna scale this puppy at work and come up with some exact dimensions...)

Why not glue some magnets on it

http://www.wondermagnets.com

and attach it magnetically? Then you can change its position at your slightest whim!

Unfortunately so could a thief...change it from the back of your box to his pocket...

Moved to DC... :lalala:

put it where you want, just make sure it's straight, lol

to left of wiper arm in center would look cool

****Disclaimer: I am not responsible for below information being accurate and in no way say that these dimensions are correct. They are based on a scaling method and subject to error. They do however give you a good idea of the placement of the rear bB emblem.***

http://www.scionlife.com/gallery/data/500/bB_rear_emblem_location_1.jpg

http://www.scionlife.com/gallery/data/500/medium/bB_rear_emblem_location_2.jpg

All dimensions are in inches. The dimensions on the outer edge of the drawings are what I have calculated to be the distance to locate the emblem on a hatch.
Note the difference between the distance from the edge of the bB emblem to the edge of the hatch varies about a 1/4 inch between the two scalings, so only use these as a guide line.

Busy at work ??? ;)

xB Nutt's looks good. this is out of the manual for the xB plate location:

2.429" from the right edge of the hatch and 6.468" up from the bottom of the hatch. don't ask me why I looked that up, but I did.
frankly, 2.5" up and 2.5" over should do it, but hey, that's your little red wagon.

http://www.scionlife.com/gallery/data/500/bB.jpg
(I'm gonna scale this puppy at work and come up with some exact dimensions...) How come we don't have that part shaded on our tails?? I was wondering where it goes too!!

This thread is probably old, hence the out of date pictures. but I wanted to ask if xB Nutt could repost the pictures that were posted or if you could contact me directly through PM so I could get some info on the bB placement.

I was trying to find some dimensions from a Japanese factory service manual but of course I don't have one of those just lying around.

I am researching the exact placement measurements for the Japanese bB so I can turn it all into a DIY article that can be posted and referenced.

Thanks for your time!

it goes in place of the xb logo...same location...

it goes in place of the xb logo...same location...

it goes in place of the xb logo...same location...

it goes in place of the xb logo...same location...