blacktoaster

Motegi M 122....ready for summer.

migmegmads

looks great. what are the specs?

blacktoaster

18×9 +35 rear with 225 40. 18x8 +35 front 215 40. Zero rubbing and flush. Dropped on df's.

bnutz313

Everyone / Anyone, I have rims on my xB and here are the specs: 18x8 with 225/40/18 tires and +45.

My question is, If I want to get the rear more flush with the front how big of a spacer would I have to run?

I'm on df210s I prefer not to pull / roll.

migmegmads

There's a post by Scionide on the site, where he shows his rear wheels being 18x8 +30mm and they were about a quarter inch from being flush. I think its in this thread towards the first half as a matter of fact. With that being said, I've seen wheels that are that spec with a 15mm spacer, and they look really good. Pretty positive no work to fenders would have to be done. What kind of wheels are they?

devilon

Finally went with something a little different, just bolted them on today. 18x8 XD Heist with 225-40-18 Nitto Motivos. Sitting on Eibach Sportlines.

jelder11

Running Tanabe df springs .Just bought 18x8.5 wheels 45 offset. What tires should I run. Any ideas.

Greg S

iTrader: (1)

If you want to stay near stock diameter then either 225/40s or 215/40s will work well. The 215s will have a noticeable stretch while the 225s, while still stretched won't be as noticeable. Both will clear your fenders with no issue.

allaboutdabox

no forget you need the flat lug nuts and not the acron cause the acron will come loose after drving for 1/2 hr

bnutz313

Ok, I curb checked my rims more that I like recently. That being said I'm going to be getting new ones. The rims I'm looking at are 18x8.5 +30 all around. Would these work on DF210s? I've tried searching to find pictures of this setup bug haven't had much luck.

wwotr

I was wondering if your XB is stock heigth in these pictures, or if you had lowered it.?
If so...by how much?

Roger

allaboutdabox

nice any other xb with the xr rims?

DREWxB08

iTrader: (1)

If i remember correct he had Tanabe DF-210"s in the front 1.7" and Tanabe NF-210"s in ther rear also 1.7" drop

allaboutdabox

anyone????

bnutz313

I'm looking at some rims with the following specs, would these fit:

Front: 18" x 8.5" +30
Rear: 18" x 10" +25

or 18" x 8.5" +30 all around

I'm on DF210s I would like to know if these would fit and how much fender work would be needed

Getfuzzy

Hey guys new to the site. I bought my wife a 2011 8.0rs and need some help with wheel, spring, tire combo info. The wheels i want are 18x8 with a +42 offset and i will be installing NF210 springs. this is the family ride so i would like to keep the ride as smooth as possible, what is the tallest tire i can run with out any fender mods. I was thinking 225/45/18. but i would like others input that have more experience than i do

xseveredveganx

Should be fine.

migmegmads

Don't RS xB's come with TRD lowering springs? If so, aren't those the same as NF210's and Eiback Pro's? Just keep your springs if you aren't looking to lower it any more than you already are, then don't waste your money.

nava89

I just painted my xxr wheels silver. I liked how they came out now I just need to paint my car white or silver.

user 7208230

iTrader: (1)

What flares are those? 5AD skirts? I feel like I might have seen them before on a SEMA type car. It looks awesome!

p.s. white and leave the flares black...