ROCKLANDTOYOTA

75331-0t010 is a GO!!! break off tabs just like it says and use double sided tape to secure. front emblem is off a SIENNA btw....

surfcitylocal

Nice. Thanks for doing the leg work.

1977FordF150

This is my rebaded iQ with Toyota front and rear badges as stated in my earlier posting. I added a small Scion badge next to the rear iQ for the Police even though my registration says Toyota.
I added an additional iQ to both sides and a 1.3 cut from a 1.3i badge that came off of a vintage Mini Cooper. The side molding were not available here in Washington, so I ordered it out of the UK.

The Brick, from my understanding, is what the assemblers on the factory floor call the iQ. So I made the decal and had my local sign company make it up for me out of chrome 3m tape. You have my permission to copy the decal if you use it on your iQ and not for resale.

I have had lots of fun driving it around town and lots of looks and questions.

___________

dfish

Looking good there, but one question. What is the symbol on the rear of the door?

Fish

1977FordF150

I think you are asking, “What is the small Scion badge next to the iQ on the rear door?” When I purchased the chrome wheels for the iQ (available through Toyota dealership parts department), I had four hub caps with a Scion center badge.
I removed the center Scion badge from the hub cap, cut off the two alignment pins and with a little 3m tape attached it next to the iQ.

I actually like all the Scion badging and signatures on the inside of the car. I would not have changed out the front and rear badges if Scion would have made the front and rear badge out of triple plated chrome.
I just think the Scion badge looks a little cheap for a car with iQ where the “Q” stands for quality. The car is built like a brick and is very solid. I don't know why Toyota took a quality build vehicle and put on a cheap badge. (Just a personal opinion)

I wanted to match up all the chrome from the badges, to the wheels, to the side molding. I believe it brings the congruent styling to the iQ.

_______

dfish

Sorry, I meant the little badge above the side door handles.

Fish

1977FordF150

I cut the "i" off a 1.3i badge that goes on a 1992-95 Mini Cooper. Available from
http://www.minisport.com/mini-spare-..._DAL10237.html

scionista

Where did you get the lower door trim? Every time I call around, they keep telling me the item is on Stop Sale. I want them very badly and I do not want to order them from outside the country. The dealer in England was charging almost $350 shipped.

1977FordF150

Back in May, I purchased the side Molding from Pentagon Toyota in Great Britain at the following website.
http://www.pentagon-toyota.co.uk/
The cost at that time for parts and shipping was $219.96. US Dollars.
It only took three weeks to get them.
There was an additional duty customs cost of $17 when I picked it up from FedEx.

scionista

Thanks for the reply. I did call them awhile ago. They quoted me higher than that. The cost here is supposed to be around $125 if they ever start selling them.

moonknight

Anybody know how to change the Scion emblem on the steering wheel to Toyota?

_______

stonecoldnimrod

I was wanting to replace my rear Scion emblem and replace it with an Autobot emblem I had, when I realized that there's 2 drilled holes that the rear emblem has to help placement of the factory emblem.
Just wanted to confirm that there's no drilled holes in the front bumper emblem.

_____________

ra1n

I actually wanted to change mine cause my reg paper says Toyota

ExtHIGHiq

I am researching this now. What I I found out so far is that the Scion emblem on steering Wheel is not sold as an individual item.
Toyota told me the same thing about the Matrix and the Corolla. I'm trying to Have my brother in law check out some possibilities of something out of Japan.

___________

ExtHIGHiq

I finally received the rear Toyota Luggage Emblem 75431-02080. I Decided to paint in satin black. 2 coats flat back and 2 coats satin Clear. After I painted the emblem I waited a couple of days before mounting. I removed the Scion logo with no trouble at all. It was almost as it knew it was going to be replaced.

To remove Scion emblem:

1. Tape off the area Surrounding the emblem
2. Tape a thick rag under the Scion emblem
3. Drench the emblem with a Goo Off type product. Let sit for about 15 minutes ( I used Goo Off, safe on the paint)
4. Carefully pull away the emblem. (Take Caution here. I used a simple screw driver. The Goo Off had already done most of the work.)
5. After removal of the Scion emblem, clean area thoroughly to remove any left over tape and Goo Off.
6. Peel backing of the Toyota emblem or use double sided automotive tape and line up the tabs and simply press on.

Fits perfect. Once I receive the Venza emblem for the front ill post that as well. I'm also going to put back the IQ emblem once I black satin that out too.

__________

ExtHIGHiq

Another shot.

surfcitylocal

Looks very nice on the back.

ExtHIGHiq

Well here it is. I finally received the front 2011 Toyota Venza Emblem. After painting it I waited 24 hours before touching it. For the most part I am happy but I want to redo it when weather is better. When I was mounting the emblem I accidentally placed it a little to much to the left. I'll redo it later just ran out of time. At this point ill need to pull and re-paint all in one day. I need a warm day for that.


I also put back on the IQ emblem after painting as well.

rogeratendale

Hi I am from the UK and I have a Toyota 1Q.
The front badge/emblem is:
Width: 6 and 1/4" (16cm)
Height: 4 and 1/4" (11cm).
The rear badge is:
Width: 4 and 3/4" (12cm)
Height: 3 and 1/4" (8cm)

I would be happy to swop badges with you or any other Scion iQ owner (if they are the same size) as we don't have Scion as a brand in the Uk and it would be cool to have an "unknown" brand on my 1Q!
Only one problem, anyone know how to get them off without breaking them?
Get out there with that 'ole measure and see!

rogeratendale

Hi I live in the UK and Toyota iQ's are pretty rare here. People even wave when they see another!
I would like to swap my Toyota badges (you guys call them emblems) on my iQ for a set of Scion iQ badges (emblems).
Scion doesn't exist in the UK so it will make my iQ unique.
My emblems are chromed plastic and are 6" wide X 4" high on the Bonnet (hood) and 4 1/2" (4.5") wide X 3" high on the boot (trunk).

If anyone would like to do a straight exchange of one set for the other then let me know. Please PM me.

_________