So if the resistors I had bought were the correct ohm and everything just the wrong physical size would they still work to replace the old ones?
|
If you can fit them, then I suppose they would still work.
|
The physical size determines the power capacity (wattage) they are rated for. Depending on which resistors you got and the resistance rating of each, i can tell you if they will work.
The reason reusing the solder is bad is because the flux (which is what cleans the joint) burns off when you solder. So the old solder will tend to pull in contaminents which are not removed if thatakes sense. |
Originally Posted by engifineer
(Post 3963572)
The physical size determines the power capacity (wattage) they are rated for. Depending on which resistors you got and the resistance rating of each, i can tell you if they will work.
The reason reusing the solder is bad is because the flux (which is what cleans the joint) burns off when you solder. So the old solder will tend to pull in contaminents which are not removed if thatakes sense. Part numbers 311-43ARCT 311-680ARCT 311-560ARCT 311-430ARCT 311-130ARCT 311-330ARCT 311-470ARCT And I figured out that I did burn up some of the LEDs so I have the gauge working all blue now I just want to find out if I can use these resistors cause I want to make it brighter. |
And if I'm not mistaken the resistance of them should be the ohms which is the number that follows "311-" in the part numbers. Also when putting the LCD screen back on the HVAC I must have had the solder on some of the prongs touching so the display shows all kinds of weird stuff. Is the LCD fried since I have plugged it in like that or can I just clean it up and have it work fine?
|
Originally Posted by kwarmbier2442
(Post 3964128)
And if I'm not mistaken the resistance of them should be the ohms which is the number that follows "311-" in the part numbers. Also when putting the LCD screen back on the HVAC I must have had the solder on some of the prongs touching so the display shows all kinds of weird stuff. Is the LCD fried since I have plugged it in like that or can I just clean it up and have it work fine?
|
super sexy thread!
|
Just wanted to show how my gauges turned out. The needles are a light purple, which looks really cool, cuz i didnt tear them apart to paint them. I scraped off the stock paintand used the purple vinyl! Sorry for the cell pic, it was dieing so i didnt have time to mess with settings
https://www.scionlife.com/forums/pic...ictureid=14472 |
Came out very nice!!! if you paint the needle white, it will make the needle glow brighter..
Do you mind if I use the picture?? Thanks.. |
Bump
|
How much for just center tach conversion?
And what are your "hours" like. Can you do weekday evenings 8ish in Fullerton? Thanks |
Originally Posted by ThisDudePaul
(Post 4011283)
How much for just center tach conversion?
And what are your "hours" like. Can you do weekday evenings 8ish in Fullerton? Thanks See the detail from here.. http://store.ledmod.com/index.php?ma...products_id=41 We are appointment based, as long as you make them ahead of time, we can schedule you in... I have a shop in Anaheim now... |
Bump
|
I want to change my gauge faces. I read through the procedures in the beginning of this thread but wanted to know if just the face swap is fairly simple or more extensive then I am thinking? Is the needle "reset" necessary? Also, does it come with a complete instruction manual. Thanks for your help!
|
Originally Posted by TotalChaos
(Post 4013218)
I want to change my gauge faces. I read through the procedures in the beginning of this thread but wanted to know if just the face swap is fairly simple or more extensive then I am thinking? Is the needle "reset" necessary? Also, does it come with a complete instruction manual. Thanks for your help!
Calibrating the needle is required, since you need to remove the needles to replace the gauge face.. Thanks.. |
Awesome! I am going to try to order one with the TRD logo on it....I appreciate the help!
|
Anyone In the long island area willing to do a Pink LED conversion for Me Message me, well talk prices :3 Super excited about my new used tc shes gotta be cute.
|
Originally Posted by Corruptelegancex
(Post 4013633)
Anyone In the long island area willing to do a Pink LED conversion for Me Message me, well talk prices :3 Super excited about my new used tc shes gotta be cute.
We have easy removal guides and 1-day turn around service... Thanks.. |
Sorry I never responded to your post Sean. Yes u may use the picture of my guages.
Ive seen the pic of the all pink guages, it looked hot! Id love to see some pink and whit ones! Please post some pics when u get them done! :) |
Private messaged
|
All times are GMT. The time now is 02:50 AM. |
© 2024 MH Sub I, LLC dba Internet Brands