Amp rack for the spare tire
Thread Starter
Junior Member
Joined: Dec 2005
Posts: 3
Amp rack for the spare tire
I have got an idea on a system and I want it to be checked out by an audiophile to make sure everything clicks for the setup as follows:
Remove sparetire and jack under driver seat for
custom amp rack in spare tire cubby for bass and good mid sound for back seat:
Sony 2 channel 165w RMS x 2 powers 6 x 9s
Sony Mono 600w RMS powers subs
Tsunami 1.2 Cap
Jensen Dual 12" bandpass w/ LED ( I know cheap and muddy 2 ohm but fuhqin hits)
6 x 9 rectangle boxes under front seat
Audiobahn 6 x 9s with 150hz bass blockers
Remove sparetire and jack under driver seat for
custom amp rack in spare tire cubby for bass and good mid sound for back seat:
Sony 2 channel 165w RMS x 2 powers 6 x 9s
Sony Mono 600w RMS powers subs
Tsunami 1.2 Cap
Jensen Dual 12" bandpass w/ LED ( I know cheap and muddy 2 ohm but fuhqin hits)
6 x 9 rectangle boxes under front seat
Audiobahn 6 x 9s with 150hz bass blockers
Banned
SL Member
Team N.V.S.
Scinergy
Scion Evolution
Scinergy
Scion Evolution
Joined: Jul 2003
Posts: 4,770
From: 886motorwerx
Sounds similar to what I'm currently running.
Arc Audio 10 inch woofers under each of the front seats, and both amps mounted where the spare used to reside and an Audioformz enclosure w/ Arc Audio 10 inch woofer that replaced the storage next to the spare tire.
Arc Audio 10 inch woofers under each of the front seats, and both amps mounted where the spare used to reside and an Audioformz enclosure w/ Arc Audio 10 inch woofer that replaced the storage next to the spare tire.
Thread Starter
Junior Member
Joined: Dec 2005
Posts: 3
With the driver side seat:
Is there a screw or option to remove the tire jack holder? I hope there isn't a rivet or some crap like that holding it down. I can't see naything so I think its arc'd or riveted. Let me know. Thanks
Is there a screw or option to remove the tire jack holder? I hope there isn't a rivet or some crap like that holding it down. I can't see naything so I think its arc'd or riveted. Let me know. Thanks
Senior Member
SL Member
Joined: Sep 2004
Posts: 472
From: SJ408-KC816-KS913
i dont undertsand what your saying???amps in the cubby right and 2 6x9 under the seats? i dont think ya need to remove the jack to get the 6x9 under your front seat...and as far as the amp you dont need amp rack just get a small sheet of metal(i can get it for ya if ya want) place under the amp and your fine..i have my 1,000 keenwood amp and it does fine.....also if your gonna do a system you might wanna consider getting low gauge wire 4 run it to a power block so if in the future you decide to go bigger evrything is there .....do it the first time ...un like me and now have to re run all of my stuff....good luck
Banned
SL Member
Team N.V.S.
Scinergy
Scion Evolution
Scinergy
Scion Evolution
Joined: Jul 2003
Posts: 4,770
From: 886motorwerx
Originally Posted by DC_Power_XB
With the driver side seat:
Is there a screw or option to remove the tire jack holder? I hope there isn't a rivet or some crap like that holding it down. I can't see naything so I think its arc'd or riveted. Let me know. Thanks
Is there a screw or option to remove the tire jack holder? I hope there isn't a rivet or some crap like that holding it down. I can't see naything so I think its arc'd or riveted. Let me know. Thanks
Keith will be the man to see once his shop is open.
He is well versed on the Scion line.
Senior Member
Scikotics
SL Member
Joined: May 2004
Posts: 1,811
From: Nor-Cal Scikotics
Originally Posted by squirrel
Keith did an awesome job on a custom 4 - 6.5 inch install.
The sig says it all...
Banned
SL Member
Team N.V.S.
Scinergy
Scion Evolution
Scinergy
Scion Evolution
Joined: Jul 2003
Posts: 4,770
From: 886motorwerx
Originally Posted by -Keith-
Thursday its mine
Keith, the Team Illusive Volvo made the JDM Theory flyer also!
Thread
Thread Starter
Forum
Replies
Last Post
minter66
PPC: Vehicles
0
Dec 15, 2014 01:45 PM
carid
General Tech and DIY
0
Dec 4, 2014 09:35 AM
