i tried searching this forum for some instructions/pics on how to install projector headlights, but i couldn't find anything... :eyebrow:
I NEED HELP!!! i just got my new projector headlights and i have no idea how to install them...
if someone has pics or at least instructions it would be very helpful!!![/b]

 

to install headlights on the tc u need to first remove the front bumper cover. there are four clips on the top (remove with a flathead screwdriver) four screws on the side inside the fender and bout 6 more on the bottom. once u get all the screws and clips off pull the bumper cover towards u on each corner (it held on by a slight L-shaped clip. once u get both side undone the bumper will come straight off. the headlights are held on by 3 bolts (2 on top and one on the side where the L-shaped bracket is on the fenders) and is clipped on towards the middle. you'll see what i mean once u get to this point. stick a flathead inside the clip and pry the tab out. at that point just do the reverse of installation to put everything back. i hope this helps. sorry i have no pictures.

 

yep what ^^^^___ said

 

this is the lights that i got...and it has wires sticking out from the little light bulbs on the bottom. i'm not sure what to connect them to. any idea? do i need to buy anything else to get it wired?

 

most of all the aftermarket headlights are just plug and play. it plugs directly into the stock plugs. the only thing with the ones u have there is that i heard it doesn't fit too well and people ended up needing to bend the metal or cut it directly where the top of the headlight goes.

 

mine didnt fit one bolt on the left side. just tighten up the other ones and you should be fine. it took me 45 min to install em. good luck

 

I think before I installed those I would run a small bead of silicone around the seal. A couple people have reported them fogging up after a little while.

Then again, I wouldn't have bought them at all, but if I had... that's what I'd do.

 

i suck at buying things for my car. i hate researching before buying and always end up with crappy stuff. i'll see if i can install them this weekend. hopefully they'll fit fine. i just wanna buy some bumper clips before i take my bumber off and break all the current clips... :eyebrow:
maybe i'll take some pics and post them - WITH DESCRIPTION ON WHAT THE HELL I'M DOING... hehe
good luck to ME :doh:

 

Just take it to a shop if you are not confident, they'll charge you like $50 bucks. Give them the finger if they ask for more.

 

To remove the bumper... http://www.club-tc.com/forums/exteri...r-removal.html

To remove the headlights... http://www.club-tc.com/forums/exteri...t-removal.html

Then reverse everything to put it back together. This was the guide I used the first time and it worked perfectly. Good luck.

 

you have to get some connectors for those wires sticking out. This post should tell you how since the headlights are probably similar. https://www.scionlife.com/forums/vie...jector+install

 

what area are u located. maybe u can get someone from SL to help u out. if u were near me i could help u.

 

i'll install them for ya!

 

did i mention that i'm un-patient.... anyhow, my buddy from work works on cars (i just found out today)... so he'll install the lights for me this wednesday.
SquallLHeart: but it doesn't mean that i didn't want you to install them and it doesn't mean that i won't be showing up to meats....
ttyl....

 

ohhh okayyyyy.. well.. my number is available if you run into any problems!

 

can you post a pic after the install?

 

i used this thread to install mine.

https://www.scionlife.com/forums/vie...jector+install

unfortunately theyre not your's exactly and they were exactly like mine but i can imagine it being any different

 

^^ i meant to say " i CANT imagine it being any different"

 

i linked her to the thread i made, hopefully it helped :D

 

picture of me??? haha...jk....of course i'll post a pic. i need to fill in my profile with pics too...