ITs 1255 am. Im working on sintalling my amp. I have a sound quest 4 awg amp kit. and an inline amp fuse holder. It says AGU fuse holder on the kit and the fuse is in. I ran the line to my battery. but i have no idea how to hook up the battery to the fuse to the wire... it dosen't look right. on both sides its got two little wires that i can see in there. idk what to do...

EDIT SUBS IN!!!

Thanks guys.

Ok next. I need another RCA to from the HU to the amp for the front channel.
besides that i need help

I need to install my new tweeters Ref 103t. and how do i wire those to the door speakers and then wire that to the amp so they run off the front channel? (sub is bridged on rear). basically need left side of car into left channel and so on and so forth.

How do i do it?

 

I have that same kit. SQK4.

You have to use the ring terminals. Solder a short piece of wire to 2 ring terminals, now connect one end to your batt and one to your fuse holder. Solder The rest of the red wire to another ring terminal and then bolt on your fuse. Place the cap on your fuse and then you should have a cable from your battery to the fuse and finally to the rear of your car.

It shouldn't be too difficult, take your time. Happy birthday btw haha.

I bought 2 of these kits, one for running my power/ground wires and the other for my Big 3. The fuses and the wire were really good quality, I was impressed. They didn't make them like this a few years ago.

 

Happy b day man ...did your amp kit come with a ring terminal for the power wire to place on the battery ??...and the fuse goes in between the battery and the line put some line den the fuse the the rest of the line and take the fuse out the holder until you run everything ... if i had my car id take pics hope it helps
edit:
x2 what he said i didnt see his post

 

i don't get that part though. so take that blue power wire. split it off using the two blue ring terminals. then some how connect that to the agu fuse holder? i see two little red plastic wire things inside. i just dont get how i tap into this fuse holder.

 

im not sure how ur fuse holder is but for mines i cut some power wire maybe like 7 8 inches long and put a ring terminal on one side and stripped the other and put that into the fuse holder and screwed it down with the screw thingys that were attached to the holder

 

ahhh!

 

Your AGU Fuse should look like this correct?



Once you've measured how far you want the fuse to be from the battery (around 12"-18"), cut the blue power wire at that point. Then, strip the wire about 1/2" to reveal the wire itself. Place the stripped end into the end of the capsule and tighten with hex key. Do the same for the other side of the fuse leading towards your amp.

 

imma post a pic

 

 

Looks fairly the same. In comparison to the image below, this is what I was describing in my last post.



Good luck with your install man! Also, Happy Birthday!

 

ok i jsut took those two little pieces out and tied down the bare wire with that screw off to the remote wiree!

 

Wait.. so you connected the remote wire straight to the battery?

 

ahhh sorry that was after a shot two on that last posts (celebrated getting the power wire through that ____ing grommet.. i ran the power wire raw into the fuse holder, tied that lil screw down and then on the other side using a ring terminal to the + (red) side of the battery and scrweed it on.

 

so really now i need help with the tweeters. the wiring for this is odd. i have 4 wires instead of two like my replacements... im gonna run Infinty 103t ref tweeters to go along with my 6022i door speakers

 

You're 21. Go out for a drink! Forget the wiring for today!

 

Car first drinks later

Congrats on your bday man, I hit 21 this year and I would do the same thing your doing right now. Drunkiness only last a night and sometimes a day lol, but sound systems last a loonnggg time. Years if installed right

Can't wait to see the finished product bud

 

well i have an issue now. of course. im going to a make a vid. when i turn the car i get a CEL, vsc is blinking and the TSC wont turn off.

 

That's definitely not good. Lol. Watching..

 

Keep both sets of wire hooked up to the new tweeter. The line runs into the tweeter and then down to the mids. The lighter colors are the positve lines.


Did you turn the car on with anything disconnected?

 

BUMP!