Limited Edition 1 of 1 '08 "ARS" xB
04-04-2009, 02:27 AM
#4
most of them were a piece of cake. just "POPS" right off. the Passenger side vent was a B!TCH to remove. I had to bend the dash up (whit the battery disconnected) and use a "stubby" screwdriver to remove the 3 screws holding it in. I considered removing the entire dash, but there is 1 bolt that was hard for me to reach, AFTER I got everything put back together I found out how to get the stubborn bolt out.
04-04-2009, 03:01 AM
#6
Junior Member
Join Date: Mar 2009
Location: Eau Claire, WI
Posts: 21
I am in the process of color matching my interior pieces as well. It is disapointing that the RS 6 did not come color coordinated as the RS 5 did.
So far I have only completed one of the back door handle as a test to see if I would actually like it.
How was getting the plastic pieces off of the steering wheel?
So far I have only completed one of the back door handle as a test to see if I would actually like it.
How was getting the plastic pieces off of the steering wheel?
04-04-2009, 07:19 AM
#8
Member
SL Member
Join Date: Oct 2007
Location: Pico Rivera, CA
Posts: 93
Originally Posted by meatcutter525
most of them were a piece of cake. just "POPS" right off. the Passenger side vent was a biscuit to remove. I had to bend the dash up (whit the battery disconnected) and use a "stubby" screwdriver to remove the 3 screws holding it in. I considered removing the entire dash, but there is 1 bolt that was hard for me to reach, AFTER I got everything put back together I found out how to get the stubborn bolt out.
04-04-2009, 07:41 AM
#9
Originally Posted by DarkBox8
Dude how did you do the pieces on the steering wheel? I looked to see how they popped off a few times but couldn't find anything!! SHARE pleaseee....
Looking good too man!
Looking good too man!
then there are 2 screws, one for each piece, holding the plastic in place.
04-04-2009, 07:52 AM
#10
Originally Posted by YZF_Bliss
I am in the process of color matching my interior pieces as well. It is disapointing that the RS 6 did not come color coordinated as the RS 5 did.
So far I have only completed one of the back door handle as a test to see if I would actually like it.
How was getting the plastic pieces off of the steering wheel?
So far I have only completed one of the back door handle as a test to see if I would actually like it.
How was getting the plastic pieces off of the steering wheel?
04-04-2009, 08:04 AM
#11
As most of you can see, there are quite a few white specs on most of the pieces.. it's not in the paint. it's dust. I cleaned it off, but the camera flash picked up what I didn't see. Also the pic of the rear hatch emblem... it had just rained, so there was a little water....
04-04-2009, 08:28 AM
#12
RIMS- 18" Enkei Em5 Platinum Bronze
custom headlight eyebrows/tint from Sun Scapes Window Tinting here in Medford, Oregon
Custom windshield eyebrow w/ TRD logo and Team AscensionPnw stkr from Sun Scapes Window Tinting
LOOK MA!!! No Muffler! Sounds GREAT!! better than TRD axle back. 3" oval Magnaflow tip. ( a little dirty)
5%window tint on all windows(except windshield)
[size=12]1 1/2" lowering springs from D1 Canada. (EBAY for $84 shipped)
custom headlight eyebrows/tint from Sun Scapes Window Tinting here in Medford, Oregon
Custom windshield eyebrow w/ TRD logo and Team AscensionPnw stkr from Sun Scapes Window Tinting
LOOK MA!!! No Muffler! Sounds GREAT!! better than TRD axle back. 3" oval Magnaflow tip. ( a little dirty)
5%window tint on all windows(except windshield)
[size=12]1 1/2" lowering springs from D1 Canada. (EBAY for $84 shipped)
06-08-2009, 04:38 AM
#13
some new mods....
BEFORE
Step 1:paint valve cover
ordered a spark plug cover, just waiting on delivery
new hvac overlays from www.customxbgauges.com
matching spedo gauge overlays are in the mail... can't wait to put them in
shark fin antenna from www.sharkfinantenna.com
BEFORE
Step 1:paint valve cover
ordered a spark plug cover, just waiting on delivery
new hvac overlays from www.customxbgauges.com
matching spedo gauge overlays are in the mail... can't wait to put them in
shark fin antenna from www.sharkfinantenna.com
06-09-2009, 04:24 AM
#17
Originally Posted by Schmohey
Looks great but your pedals aren't matching!
it's what I found here at a local speed shop.. have you found any "RED" ones that would match better? let me know...
06-09-2009, 08:59 AM
#18
Junior Member
Join Date: Aug 2007
Location: Pasadena, MD
Posts: 5
Originally Posted by DarkBox8
Dude how did you do the pieces on the steering wheel? I looked to see how they popped off a few times but couldn't find anything!! SHARE pleaseee....
Its a size 25 star drive, there's a hole on either side of the steering wheel like ole boy said.
