T3/t4 turbo clearance issues.
#1
T3/t4 turbo clearance issues.
Hey everybody! This is my first time posting in a year or so, so don't burn me too hard.
Anyways, long story short, I'm slowly collecting parts to make my own turbo kit, and so far I have a goodspeed t3/t4 turbo and their cast manifold. I went to mock it up today to start fabricating the intercooler piping as well as the down tube and wastegate dump. Well everything went fine as far as removing the stock manifold and cat, and installing the turbo manifold was a cake walk, but then I go to bolt up the turbo, and it seems like everything that exists in the engine bay wants to fight me... I rotated the compressor housing in every possible direction but nothing seemed to help, so I removed the electric fans. Now the turbo is able to bolt up to the manifold, and I believe I have enough room to fabricate a dump pipe and run the i/c piping, but I can't get the electric fans back in. Now it seems to me that I have two options, send the manifold back and buy one with the flange moved back twords the engine about 3/4", or buy some slimmer electric fans. But before I do either of those, I would like some opinions from you guys on here. I have mad respect for some of you and would like to see if you can offer anything else.
BTW, I know that everyone and their mom hates on cast manifolds and the godspeed brand, and that they are not good for power, but I am literally only planning on running 5 PSI. This is not a race car, it's my DD, and I just want a little something that I can show off with.
Thank you all in advance for your helpful suggestions.
Anyways, long story short, I'm slowly collecting parts to make my own turbo kit, and so far I have a goodspeed t3/t4 turbo and their cast manifold. I went to mock it up today to start fabricating the intercooler piping as well as the down tube and wastegate dump. Well everything went fine as far as removing the stock manifold and cat, and installing the turbo manifold was a cake walk, but then I go to bolt up the turbo, and it seems like everything that exists in the engine bay wants to fight me... I rotated the compressor housing in every possible direction but nothing seemed to help, so I removed the electric fans. Now the turbo is able to bolt up to the manifold, and I believe I have enough room to fabricate a dump pipe and run the i/c piping, but I can't get the electric fans back in. Now it seems to me that I have two options, send the manifold back and buy one with the flange moved back twords the engine about 3/4", or buy some slimmer electric fans. But before I do either of those, I would like some opinions from you guys on here. I have mad respect for some of you and would like to see if you can offer anything else.
BTW, I know that everyone and their mom hates on cast manifolds and the godspeed brand, and that they are not good for power, but I am literally only planning on running 5 PSI. This is not a race car, it's my DD, and I just want a little something that I can show off with.
Thank you all in advance for your helpful suggestions.
#2
Turn it so the cold side is facing down. If it ends up not being able to fit, get an aftermarket radiator and some slim fans and mount them on the outside blowing air towards the radiator.
#6
take the manifold and turbo of as a whole, rotate the turbo so the outlet faces down leave it loose so you can slightly roatate as its in the car, that turbo shold have no issues with the fan shroud off, i ran a 60-1 with the same manifold ad stock radiator
#8
#9
p-tuning and dezod have a great set of fans. I dont trust the mish fans and ill tell you why. At first they work just fine but over time the fan shaft will rust and slow down the fan speed, next thing you know they just wont knock the heat down.
the p-tuning fans are set up as push-pull configuration. I think dezod's is set up the same way. one fan will mount where the motor will face the bumper and the other will mount so the motor will face the engine.
the p-tuning fans are set up as push-pull configuration. I think dezod's is set up the same way. one fan will mount where the motor will face the bumper and the other will mount so the motor will face the engine.
#11
Just looked up both the fan kits and they are both way out of my budget for this paycheck lol. But from my perspective the slim fans seem to be cheaper then getting a different manifold. Looks like my project gets to wait a few more weeks.
Oh hey! By the way, does anybody have a 35 or 38mm wastegate that you want to get rid of? I figured the w/g is the only thing I don't want to go cheap on, and I've got my mind set on a 38mm tial.
Oh hey! By the way, does anybody have a 35 or 38mm wastegate that you want to get rid of? I figured the w/g is the only thing I don't want to go cheap on, and I've got my mind set on a 38mm tial.
#13
#16
#18
BTW, I know that everyone and their mom hates on cast manifolds and the godspeed brand, and that they are not good for power, but I am literally only planning on running 5 PSI. This is not a race car, it's my DD, and I just want a little something that I can show off with.
#20