tC Seat controls

Reply Subscribe

Thread Tools

Search this Thread

Jul 4, 2004 | 01:42 AM

nero_tC

Thread Starter

Senior Member

SL Member

Joined: Jul 2004

Posts: 446

tC Seat controls

what is the lever all the way on the left move? the circular looking one? i know the right one is to decline the seat and the middle one is to move the seat up and down but what about the last one on the left?

http://www.clubsciontc.com/modules.p...album=5&pos=27

Jul 4, 2004 | 01:51 AM

fr130

Banned

SL Member

Joined: Dec 2003

Posts: 630

It's the lumber adjustment ****. When you are sitting on the seat, use the **** move it clockwise or counterclockwise. You'll feel the seat area close to your kneecaps go up and down.

Jul 4, 2004 | 04:52 AM

scion_jC

Senior Member

SL Member

Joined: Jul 2004

Posts: 168

whats this i heard of the tC having some sort of "seat memory" ?

Jul 4, 2004 | 05:01 AM

05_Flint_tC

Senior Member

SL Member

Joined: Jun 2004

Posts: 134

From: Irving, TX

it's nothing special. when you slide the seat forward to let the rear passengers out, the seat will go back to it's original position. i can think of 5 cars off the top of my head that do that as well.

Jul 4, 2004 | 12:20 PM

pvt_joker

Member

SL Member

Joined: Jul 2004

Posts: 73

From: filthydelphia

the know does adjust under your kneecaps, but that's not lumbar support....lumbar is your lower back

Jul 4, 2004 | 12:33 PM

nero_tC

Thread Starter

Senior Member

SL Member

Joined: Jul 2004

Posts: 446

That had me a little confused there. I still don't think I understand what that **** is for. Doesn't the middle one move the seat up and down which adjusts the knee room? Why the additional **** on the left?

Jul 4, 2004 | 03:01 PM

jlaznlover

Senior Member

SL Member

Joined: Jun 2004

Posts: 933

From: Orlando, FL

i've only sat in the tc only a few times. the far left **** moves the front of the seat up and down(the very front tip of the seat lol dont know how to explain it

) the one all the way on the right should just tilt the seat, and the middle one is the one i think you use to let someone out of the back. hmmm... im probably wrong, i need to test that out again... doh... i want my tc!!!

Jul 4, 2004 | 08:39 PM

chipmOnk

Senior Member

SL Member

Joined: Jun 2004

Posts: 395

From: Bay Area

Quote:

Originally Posted by fr130

It's the lumber adjustment ****. When you are sitting on the seat, use the **** move it clockwise or counterclockwise. You'll feel the seat area close to your kneecaps go up and down.

you do know that lumbAr support is for your back right?

i'm pretty sure the **** is for adjusting the angle of actual part where your legs sit...

Jul 11, 2004 | 07:27 PM

jlaznlover

Senior Member

SL Member

Joined: Jun 2004

Posts: 933

From: Orlando, FL

i tested the seats out again today. turns out the lever in the center moves the rear of the seat up and down(the butt of the seat, lol) i had issues with the headroom because i didnt know that the lever actually did that until i tried it out. so the first couple of times with i actually sat in the car the seat height was actually at its highest or tallest setting. that explains why there was no head room(im 6'0) when i put it at the lowest setting. its just fine :D